Exactly how to Replace a Tub (Step By Step).
Exactly how to Replace a Tub (Step By Step).
Blog Article
This post in the next paragraphs on the subject of Installing A Bathtub is relatively enjoyable. Don't overlook it.
Installing a bathtub isn't exactly rocket science, yet it does need strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a new one is also a moderately challenging project. If the old bathtub is easily available, the job can move speedily; if you need to open up a wall surface to eliminate the old bathtub as well as position the new tub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will need an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the job and also fit trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to take into consideration using one prior to you begin. Possibilities are you may need a specialist plumber to make tube links.
This post will help you install a brand-new tub in your shower room if you have currently acquired a new bathtub as well as do not require to change the arrangement of your previous water pipes.
Your devices as well as product checklist should comprise the following:
Planning for the Setup
To start with, the supporting structure supplied with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will have to be cleaned of any old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the called for placement. The wooden boards are valuable in evenly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub until the spirit level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and inspect all joints and new pipework for leakages and tighten them if essential. Fill up the tub and additionally examine the overflow outlet and also the typical outlet for leakages.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the bathtub should wait till the tub has been made use of a minimum of when as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washing machines are in area between the tap as well as the sink. Secure the faucet in position with the manufacturer given backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to break a stiff seal, triggering the water to permeate the wall surface in between the bath and the tiling, causing difficulties with dampness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly load the tub with water prior to securing, to enable the movement experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that write up about How to Install a Bathtub Yourself while doing a search on the web. Sharing is good. You never know, you may be doing someone a favor. I appreciate reading our article about Installing A Bathtub.
Explore Now Report this page